济南模型公司
  • 山东省济南市槐荫区古城
  • 商业街(山东省肿瘤医院西邻)
  • 电话:0531-55504101
  • 传真:0531-86013022
  • 手机:18660800958 13869134430
新闻中心当前位置:首页-新闻中心
    沙盘模型动态水如何制作
    2016-7-5 13:51:00
    所谓动态水,就是借助水体制作的基本材料以外,使用其他媒质营造水体流动的真实感觉。即水循环系统和流水灯光控制系统。
    The so-called dynamic water, is the use of water produced by the basic materials, the use of other media to create a real sense of water flow. Water circulation system and water light control system.
    1.水循环系统
    1 water circulation system
    沙盘模型的水循环系统主要包括:潜水泵,储水池,上下水管,模型防水通道,水池或河道(水区域的容器)等,形成真水循环系统。
    The sand table model of water circulation system mainly includes: submersible pump, tank, pipe, waterproof model channel, pool or river container (water area), forming water circulation system.
    首先做好水池或河道(水区域的容器)的防水工作,可选用防水胶对水池或河道做防水处理,在水池或河道的适当位置安装下水管,下水管可高出底部1cm,以保证水区域内始终有水。同时要注意下水管的安装要隐蔽,一般可以隐藏在假山内或是水池下。上水管为了避免水压过大造成的喷射水流过远,可在出水口安装挡片,使水流舒缓自然。可在出水口和水面之间增加山石,制作瀑布、泉涌、叠水等效果。或是直接在出水口连接不同粗细的医用针头,模仿各种喷泉的效果。
    First do a good job in pond or river (regional water containers) waterproofing work, can choose waterproof glue on the pool or river do waterproof processing, pipes installed in proper position of the pool or river, the drainage pipe can be high at the bottom of the 1cm, to ensure that there will always be a regional water water. At the same time, pay attention to the installation of the water pipes to be hidden, can be hidden in the rockery or pool. Water in order to avoid excessive water pressure caused by the jet is too far away, can install the outlet baffle, the flow of water to relieve nature. Can increase the rocks between the water outlet and water, making the waterfall, Quanyong, cascading effect etc. Or is the medical needle connected with different thickness directly at the outlet, imitate a variety of fountain effect.
    2.流水灯光控制系统
    2 light water control system
    这种方法的实质是通过灯光的控制营造水流的效果。第一种是简易的彩灯控制器,通过两个电子开关交替导通达到近似水流的效果,用电位器来实现频闪速度,使流水有交替闪光的效果。第二种是选用可编程控制器,通过单片机控制,可以预先烧录好控制芯片,按设计需要控制闪光,实现多点控制,这是目前水体灯光控制器最为人性化的形式,可以营造潺潺流水,美轮美奂的效果。

    The essence of this method is to create the effect of water flow through the control of light. The first is simple lantern controller, through two electronic switch alternate conduction to approximate the flow effect, potentiometers for use to achieve speed strobe, the flash alternately the effect of water. The second is to use programmable controller, through the control of the microcontroller can be pre burn a good control chip, according to requirements of design, flash control, multipoint control, this is the water lights controller is the most humane form, you can create a gurgling water, beautiful effect.

    本文由淄博模型公司整理发表提供,详情请关注公司网站:http://www./

    版权所有:济南市槐荫区视野模型设计制作中心  Copyright @ 2011-2012  电话:18660800958  传真:0531-55504101  鲁ICP备11014722号  地址:济南市槐荫区古城商业街  网址:www.  
友情链接:    幸运飞艇导航   9999彩票   诚信彩彩票手机app下载   9号彩票   热购彩票