济南模型公司
  • 山东省济南市槐荫区古城
  • 商业街(山东省肿瘤医院西邻)
  • 电话:0531-55504101
  • 传真:0531-86013022
  • 手机:18660800958 13869134430
新闻中心当前位置:首页-新闻中心
    静态模型制作中的打磨和涂漆技巧
    2017-5-15 13:46:01
    工业模型在制作模型的时候,第一步就是打磨,在打磨过程中需要注意很多地方,本文提供一些模型打磨和涂漆的经验技巧。
    Industrial model at the time of making model, the first step is to burnish, need to pay attention to many places in the grinding process, the paper provides some model grinding and painting skills.
    当模型组合好后,模型表面会有许多夹缝,这样会严重影响模型的外观,所以必须要对模型夹缝进行修补。主要的工具是补土、锉刀和砂纸。另外要注意的是模型在组合时必须下胶水,否则夹缝修补后很易又裂开。补土也叫不地,是专门用来填补模型夹缝的一种有机树脂。种类也有许多,一般较常用的是田宫公司的。在许多较大的模型店都有售。使用时用适当的工具沾取适量抹在想填补的接合线上或凹处,抹的时候要施加一定的压力,将补土填满凹处的每一角落。补土的成份中含有可溶解塑料的溶液,所以接触到模型表面时不易脱落。但因其中的溶液会挥发,所以当它完全干燥硬化后体积会缩小一点。当我们上补土时就要多补一点。使补土有足够体积应付打磨需要。
    When the model is assembled, there will be a lot of cracks in the surface of the model, which will seriously affect the appearance of the model, so it will be necessary to repair the cracks in the model. The main tools are soil, file, and sandpaper. The other thing to note is that the model has to be glue when it is assembled, otherwise it will be easy and open. Supplementary soil is also called "no", a kind of organic resin that is used to fill the cracks in the model. There are also many kinds, generally more commonly used by tian gong company. It is available in many larger model stores. When used with the appropriate tools to touch take right amount put in to fill the joint line or sunken place, apply a certain pressure, when you need to fill soil fill every corner of the concave. A solution of soluble plastic is contained in the composition of the soil, so it is not easy to fall off when exposed to the surface of the model. But because the solution is volatile, it shrinks a little when it is completely dry and hardened. We need to make a little more when we fill the soil. Fill the soil with sufficient volume for grinding.
    等补土完全干后(约四五小时)就可以进行打磨了。先用锉刀锉,要顺着弧度,当锉得差不多时(要自己判断)就换砂纸打磨。砂纸号码越大,代表颗粒越细。通常先用400号,再用600号、800号。使用800号以上的砂纸时最好沾一点水来打磨,这样表面会更平滑。有时补土会填了模型的凹线,这时可在补土未干时用刻刀或牙签刻回凹线。打磨好后就要喷上一层水补土,它是液状的,主要能检查修补打磨的情况。同时它是浅灰色的,可以用来作模型的底色。当发现要再修补时就要放上一天,等水补土干后再修补打磨。
    After the soil is dried up, it will be ready to be sanded. File the file with a file, follow the radian, and when the file is similar (make your own judgment), the sandpaper is polished. The larger the sandpaper number, the finer the grain. Usually we use 400 first, then 600, 800. Use more than 800 pieces of sandpaper and it is best to rub a little water to make it smoother. Sometimes the soil will fill in the concave of the model, and then it will be cut back to the concave line when the soil is not dry. When it is finished, it will be sprayed with water to fill the soil. It is liquid, and it will be able to check for the repair and polishing. It is also light grey, which can be used as a base color for the model. When you find out you're going to fix it, you're going to put it up for a day, and then you'll fix it when the water is dry.
    下面介绍涂漆的方法。打磨好后就可以上色了。大家可以用手涂也可以用喷笔。手涂优点是可以涂一些较细的地方,不过涂较大面积时就容易出现笔痕。喷笔喷大面积时十分均匀,油层比较薄,效果比较好,但细小的地方就要用分色纸,比较麻烦。
    Here's how to paint it. When you're finished, you can color it. You can also use your hands or you can use a pen. The advantage of the hand is that you can apply some of the finer points, but it is easy to get a pen mark when applied to a large area. Spray pen spray large area is very even, the oil layer is thinner, the effect is better, but the small place is about to use cent colour paper, compare trouble.
    常用的模型油漆一般有水性油漆和油性油漆。我个人觉得油性比较快干,手涂时较均匀,而水性就比较适合用于喷笔。要注意的是水性和油性两种油漆是不能混合的。而且使用前必须稀释。
    The commonly used model paint is usually water-based paint and oil paint. I personally think oily is quick drying, the hand besmear is more evenly, and the water is more suitable for the pen. It is important to note that water and oil are not mixed. And it must be diluted before use.
    上色前先搅拌油漆使之均匀。用笔毛较软的画笔沾一些涂料,并在瓶口轻刮一下,调节笔上的含漆量。下笔时由左至右,以稳定均匀的力道移动。涂完第一笔后,下一笔也是由左至右涂,并且和第一笔的边缘重叠一点点。下笔时力道要轻,要有让笔上的油漆轻轻流在表面的感觉,动作越轻,笔痕越不明显。涂的时候要注意何时要再沾上油漆,不要等到笔上没油漆才沾上,要尽量保持画笔在湿润状态。等第一层油漆差不多干时(七八成吧),可以上第二层油漆,方向和第一层垂直。这叫“十字上色法”。上第二层色力道和方向要更小心。因为第一层还未干透,太大力会刷起第一层。当第一层油漆未干透再加上第二层新漆,这样就比较容易处理好笔痕,使之不明显。
    Stir the paint before coloring to make it even. Use a brush with a soft brush to touch the paint and gently scrape the top of the bottle to adjust the amount of paint on the pen. When the pen is down, it will move from left to right, with a steady and uniform movement of force. After finishing the first pen, the next one is also painted left to right, with a slight overlap with the edge of the first pen. The lower pen is lighter, and the lighter the paint on the pen, the lighter the movement, the less visible the ink. When you apply it, be careful when you have to apply the paint, don't wait for the paint to stick, try to keep the brush wet. When the first layer of paint is almost dry (7, 80), you can get the second layer of paint, which is perpendicular to the first layer. This is called "cross color". Be more careful with the second layer of color and direction. Because the first layer is not dry, the first layer is too much. When the first layer of paint is not dry and the first layer of new paint is added, it is easier to deal with the scratch and make it less obvious.
    另外,如果模型的底色比较鲜艳,而涂上的颜色遮盖力又弱,这样颜色看起来就不均匀了。所以最好先上一层白色或浅灰作底色。这样效果才比较理想。
    In addition, if the base color of the model is brighter, the color of the paint is weak and the color looks uneven. So it's best to start with a white or light gray. The effect is ideal.
    版权所有:济南市槐荫区视野模型设计制作中心  Copyright @ 2011-2012  电话:18660800958  传真:0531-55504101  鲁ICP备11014722号  地址:济南市槐荫区古城商业街  网址:www.  
友情链接:    9号彩票   热购彩票   幸运飞艇导航   全民彩票   98彩票